Showing 1–24 of 26 results

Check Valves (9)

Check Valves - Intank (2)

Tank & Slide Valves (3)

Compressor Valves (1)

Relief Valves (8)

Unloader Pilot Valves & Throttle Valves (4)

1/4” – 3/8” ASME Safety Relief Valves (Control Devices)

A compact, high flow rate safety valve. All brass construction with resilient silicone seat seal results in a bubble tight

1/2” ASME Safety Relief Valves (SF-50) (Control Devices)

High flow rate safety valve. All brass construction with resilient silicone rubber seat seal results in a bubble tight seal

1” – 1 ¼” ASME Safety Relief Valves (Control Devices)

High flow rate safety valve. Brass construction Resilient Silicone rubber seat Bubble tight to within 10% of set pressure. Maximum

3/4” – ASME Safety Relief Valves (Control Devices)

High flow rate safety valve. Brass construction Resilient Silicone rubber seat Bubble tight to within 10% of set pressure. Maximum

Ball Check Valve – Brass

400 psi maximum size ¼” to 2” 210° F maximum temperature 0.5 psi cracking pressure Model Size BC-2 1/4” BC-3

Ball Check Valve – Stainless Steel

400 psi maximum size ¼” to 2” 175 psi maximum 2 ½” to 3” 210° F maximum temperature 0.5 psi

Cast Brass Check Valve (Control Devices)

250 psi maximum 450° F maximum temperature Cracking Pressure < 3 psi Model Size CB-13 1/8” CB-25 1/4” CB-38 3/8”

Check Valve – Female – Female

212 psi maximum 40° F to 140° F Nickel Plated Brass Model Size CV-1 1/8” CV-2 1/4” CV-3 3/8” CV-4

Check Valve – Female – Female 2000 psi maximum

2000 psi maximum -20° F to 212° F Brass Model Size BC 125B 1/8” BC 250B 1/4” BC 375B 3/8”

Check Valve – Male-Male (Control Devices)

250 psi maximum 40° F to 250° F Brass Model Size M2525 1/4”

Cold Start Valve (Control Devices)

CS -12 and CS -25 valves bleed air from the compressor head during the first few revolutions, thus reducing motor

LGM 30 Load Genie – Continuous Run Unloader (Control Devices)

The Load Genie Mark LGM 30 replaces the conventional three component system with all the economic advantages including elimination of

Inline Check Valve (Control Devices)

IC valve can be installed in the discharge line of the compressor whenever an in-tank valve will not fit, and

Intank Check Valve – Compression Fitting (Control Devices)

Model Material SCFM Tube Comp MPT outlet C5038-STA Brass 20 1/2” 3/8” C5050-ST Brass 20 1/2” 1/2” SC1212 Steel 20

Intank Check Valve – NPT Threads (Control Devices)

Model Material SCFM FPT inlet MPT outlet P5050-ST Brass 20 1/2” 1/2” S1212 Steel 20 1/2” 1/2” P5075-ST Brass 30

Low Pressure Relief Valve (PR-25) (Control Devices)

Model PR low pressure relief valves are used in systems to maintain a desired pressure level. Model PR is a

Non Code Relief Valve (Control Devices)

This safety valve though miniature in size has been designed to give high flow performance. NC valves incorporate many of

P25 Unloader Pilot Valve (Control Devices)

Variable Range and Differential This Unloader Pilot Valve fills the need for a control that can be adjusted both for

High Capacity ASME Side Port Relief Valves (Control Devices)

Side vent ASME safety valve designed for large flow capacities Pull Ring design O Ring seal is bubble tight to

Slide Valve

Allows full flow in one position and block supply pressure and exhausts downstream pressure in other position. Brass 250 psi

Swing Check Valve

Bronze Construction Operating Temp. 200° F Max. Pressure 150 psi Full flow and can be installed vertically or horizontally Recommended

Tank Manifolds (Control Devices)

Model Application ACM Air Compressor CTM Carry Tank

Tank Valve (Control Devices)

Tank valves are used wherever a method of inflating a tank with a standard air chuck is required. Brass body,

Throttle Control (Control Devices)

TC throttle controls are used on gas engine-driven compressors to reduce engine speed to idle when the continuous run control